How to Make Checkerboard Cutting Board in 10 Steps

A checkerboard cutting board is made by gluing alternating light and dark hardwood strips into a panel, crosscutting that panel into equal slices, turning the slices so their end grain faces upward, and reversing every other row. After a second glue-up, the board is flattened, sanded, and finished with food-grade mineral oil.

The biggest challenge is keeping every square aligned. Slight differences in strip width, uneven saw cuts, or excessive clamping pressure can leave gaps and crooked checkerboard lines. Correcting those mistakes after the final glue-up can require substantial sanding or removal of wood.

Accurate measurements and a careful assembly sequence produce a board with clean contrasting squares, tight joints, and a smooth cutting surface. The end-grain construction also provides a forgiving surface for kitchen knives.

Woodworking safety deserves attention during this project. In a 2023 rulemaking analysis, the U.S. Consumer Product Safety Commission estimated approximately 30,000 emergency department-treated table saw blade-contact injuries in 2021. Proper guards, a riving knife, push devices, and securely supported crosscuts are important when making small wooden components.

What stood out to me while researching how to make checkerboard cutting board patterns was how much the second assembly stage determines the finished appearance. Rotating the cut pieces exposes the end grain, but reversing alternating rows is what turns ordinary stripes into a checkerboard.

For a manageable project, I recommend starting with hard maple and black walnut. Their contrasting colors create a traditional checkerboard appearance without stains or dyes. Using matching strip dimensions also makes the layout easier to calculate.

The instructions below cover the materials, tools, measurements, two glue-ups, cutting sequence, safe flattening methods, and final conditioning. A worked example shows how to create a board approximately 12½ × 15 inches before final edge trimming.

What Is a Checkerboard Cutting Board?

How to Make Checkerboard Cutting Board in 10 Steps

A checkerboard cutting board is a wooden preparation surface made with alternating light and dark squares, similar to the pattern on a chessboard.

Most traditional handmade versions use end-grain construction, meaning the short ends of the wood fibers face upward on the cutting surface.

A standard edge-grain board exposes the long sides of wood fibers. An end-grain board exposes their ends, creating a different response when a knife contacts the wood.

This construction is popular for butcher blocks because the blade can move slightly between the exposed fibers during chopping.

The checkerboard pattern usually comes from two contrasting hardwood species. Hard maple forms the lighter squares, while black walnut creates the darker squares.

The pattern does not require staining, painting, or individual assembly of dozens of small cubes.

Instead, carefully arranged hardwood strips are glued, crosscut, rotated, and glued again. This two-stage process produces a consistent pattern with far fewer individual pieces to handle.

Materials and Tools Needed to Make a Checkerboard Cutting Board

Preparing the correct materials before cutting reduces measurement mistakes and interruptions during assembly.

The project requires two hardwood colors, an adhesive suitable for cutting boards, accurate cutting tools, and a way to flatten the finished end-grain surface.

Best Wood for a Checkerboard Cutting Board

Hard maple and black walnut are my preferred combination for this project.

Hard maple has a pale cream appearance and a Janka hardness rating of approximately 1,450 pounds-force. Its fine grain and resistance to dents make it well suited to cutting boards.

American black walnut has a dark brown appearance and a Janka hardness of approximately 1,010 pounds-force. It is softer than maple but provides a forgiving cutting surface.

These woods create strong visual contrast without requiring decorative coatings.

Other suitable combinations include maple with cherry or beech with walnut, although the contrast may be less dramatic.

Choose clean, kiln-dried hardwood that has been stored in a stable indoor environment. Avoid lumber with large cracks, loose knots, severe twisting, or unknown chemical treatments.

For this project, use wood intended for food-contact applications rather than pressure-treated, painted, or chemically preserved lumber.

The FDA’s Food Code identifies hard maple and equivalently hard, close-grained woods as acceptable cutting-board materials in its model food-service standards.

Choosing Cutting-Board Glue and Finish

The first and second glue-ups require a moisture-resistant wood adhesive suitable for cutting-board construction.

Titebond III Ultimate Wood Glue is a common option.

Its manufacturer identifies it as compliant with U.S. FDA requirements for indirect food contact and states that it meets the ANSI/HPVA Type I water-resistance specification.

Allow the adhesive to cure according to its instructions before further machining or exposing the board to food.

For the final finish, use food-grade mineral oil specifically sold for cutting boards.

A mineral-oil-and-beeswax conditioner can be applied afterward if desired.

Avoid ordinary vegetable oil or olive oil for conditioning because these oils may become rancid.

Also avoid decorative wood stains and finishes that are not intended for repeated food preparation and direct knife contact.

Tools and Safety Equipment

The following tools are suitable for a standard end-grain checkerboard project:

  • Table saw with a sharp blade, blade guard, and riving knife
  • Crosscut sled or another properly supported precision crosscutting setup
  • Jointer and thickness planer for preparing the initial long-grain stock, or pre-milled lumber
  • Bar clamps or parallel-jaw clamps
  • Square, ruler, and measuring tape
  • Glue spreader and protective clamping cauls
  • Router sled or drum sander for flattening the final end-grain board
  • Random-orbit sander and sandpaper
  • Router with an edge-rounding bit, if desired
  • Eye protection, hearing protection, and suitable dust protection

A reliable crosscut sled is useful because the checkerboard pattern depends on repeated cuts of identical thickness.

Use push sticks or push blocks for ripping narrow strips, following the saw manufacturer’s safety requirements.

Never hold small pieces freehand near a spinning saw blade.

Key Takeaway: Hard maple and walnut provide clear color contrast and suitable cutting characteristics. Use a cutting-board-compatible adhesive, accurately milled stock, and a safe method for flattening end grain.

Checkerboard Cutting Board Measurements and Cut List

A measured cutting plan prevents mismatched square sizes and unnecessary waste.

For this example, the finished board will contain 120 alternating squares, arranged in 10 columns and 12 rows.

Example Dimensions for a Maple and Walnut Board

Use five maple strips and five walnut strips, each milled to the same dimensions.

ComponentQuantityPrepared Dimensions
Hard maple strips51¼ × 1¼ × 24 inches
Black walnut strips51¼ × 1¼ × 24 inches
First glued panel1About 12½ × 24 × 1¼ inches
Crosscut slices121⅝ inches wide along the original panel length
Pattern squares120About 1¼ × 1¼ inches
Final board1About 12½ × 15 inches before edge cleanup

The 1⅝-inch crosscut measurement provides extra material so the finished board can be flattened to approximately 1½ inches thick.

Final dimensions will be slightly smaller after squaring the edges and smoothing the surfaces.

The 24-inch strip length provides space for twelve slices, saw kerfs, and end trimming.

These measurements are a practical example rather than a required cutting-board size.

Why Equal Strip Width and Thickness Matter

The visible checkerboard squares come from two original stock dimensions.

The width of each hardwood strip becomes one side of a square.

The original thickness of the wood becomes the other side after the crosscut pieces are rotated upright.

For square blocks, those two measurements should match.

In this example:

1¼-inch strip width × 1¼-inch original thickness = 1¼-inch checkerboard squares.

The 1⅝-inch crosscut dimension serves a different purpose. It determines the thickness of the finished board after the slices stand upright.

The number of original hardwood strips also matters.

Using an even number of alternating light and dark strips makes it possible to reverse every other row and create the checkerboard pattern without shifting or trimming individual squares.

I recommend marking the prepared strips before assembly so their order is easy to maintain.

Key Takeaway: Match the original strip width to the wood thickness for square blocks. Use an even number of alternating strips and allow extra thickness for final flattening.

How to Make Checkerboard Cutting Board Step by Step

The construction process uses two separate glue-ups.

The first creates a striped wooden panel. The second converts the crosscut slices into a checkerboard with their end grain facing upward.

Step 1: Plan the Pattern and Prepare the Work Area

Begin by confirming the finished board dimensions and number of squares.

For the measured example, the pattern has ten squares across and twelve rows from front to back.

Arrange a flat assembly surface with enough space for clamps, wood strips, and tools.

Check the cutting equipment before starting.

Make sure the table saw is properly adjusted and the blade, guard, and riving knife are suitable for the planned cuts.

Prepare a flat surface for dry fitting the pieces before applying glue.

I recommend making a simple pencil sketch showing the alternating colors.

For example, the first row begins with maple, followed by walnut, maple, walnut, and so on.

The next row will begin with walnut.

This color arrangement becomes important after the crosscut pieces are turned upright.

Step 2: Cut and Mill the Hardwood Strips

Prepare five maple strips and five walnut strips to the same dimensions.

For this example, each strip should measure 1¼ inches wide, 1¼ inches thick, and 24 inches long.

Start with lumber thick enough to produce these dimensions after milling.

If working from rough lumber, establish one flat face and one straight edge using the appropriate machinery and procedures.

Mill the remaining surfaces until each strip is flat, square, and consistent in size.

Use the table saw to rip the strips to their required width with a suitable fence, guard, and push device.

Do not attempt to straighten a severely warped board by forcing it against the table saw fence.

If you do not have suitable milling equipment, purchase pre-milled hardwood and have it prepared to matching dimensions.

Check every strip with a square.

Even a small difference in thickness can prevent the final checkerboard rows from lining up cleanly.

Step 3: Arrange the Strips in Alternating Colors

Lay the ten prepared strips next to each other on a flat bench.

Arrange the sequence:

Maple – Walnut – Maple – Walnut – Maple – Walnut – Maple – Walnut – Maple – Walnut

All strips should run in the same lengthwise direction.

Their ends do not have to be perfectly aligned yet because they will be trimmed after gluing.

Check the joint surfaces.

Adjacent strips should touch along their full length without visible gaps.

If gaps appear, correct the mating edges before gluing.

Number the strips lightly with a pencil or use temporary labels to preserve their order.

Check the growth-ring orientation where practical, but do not sacrifice straight, well-fitting glue surfaces to obtain a particular ring pattern.

Step 4: Glue the Strips Into the First Panel

Apply an even layer of cutting-board-compatible wood glue to the mating edges.

Spread the adhesive across the complete joint surfaces rather than placing isolated beads.

Bring the strips together in their original sequence.

Use clamps to apply even pressure across the panel.

A small amount of glue squeeze-out indicates that the joint surfaces have received adhesive.

Avoid excessive pressure that forces the strips out of alignment.

Place protective cauls between clamp jaws and the hardwood to reduce dents.

Check that the top surfaces remain level and that the assembled panel is not twisted.

Remove accessible excess adhesive according to the glue manufacturer’s instructions.

Allow the first assembly to cure before machining.

Titebond recommends avoiding stress on a newly glued joint for at least 24 hours under typical conditions. Low temperatures, high moisture, and other conditions may require more time.

Step 5: Flatten and Square the First Glued Panel

After the adhesive has cured, remove the clamps and inspect the striped panel.

Check for gaps, loose strips, and uneven glue joints.

At this stage, the original hardwood grain still runs lengthwise through the panel.

A properly operated thickness planer may be suitable for flattening this long-grain panel, subject to the machine’s requirements.

A router sled or suitable sanding equipment is another option.

Remove only enough material to flatten the surfaces.

Remember that the finished square dimensions depend on the actual panel thickness.

If the panel becomes thinner than planned, adjust the intended square dimensions or accept slightly rectangular blocks.

Square the ends and check that the panel edges are straight.

Do not proceed until the first panel has solid joints and a flat surface.

Step 6: Crosscut the Panel Into Equal Slices

This step produces the individual rows that will form the checkerboard.

Place the striped panel in a properly sized crosscut sled or another supported crosscutting setup.

Set the cutting system to produce slices measuring 1⅝ inches along the original panel length.

The extra ⅛ inch provides material for flattening the finished board to approximately 1½ inches thick.

Make the first cut to square the panel end.

Then cut twelve equal slices, accounting for the saw kerf and the remaining panel length.

A repeatable stop system improves consistency, but it must not trap an offcut between the blade and a fixed fence or stop.

Support the workpiece securely and keep hands outside the blade area.

Do not reach near the blade to retrieve small offcuts while it is moving.

Each completed slice should contain the full maple-and-walnut sequence across its length.

Number the slices in pencil so their order can be restored during dry fitting.

Precision Tip: If one slice is thicker than the others, it can create a raised area in the final board. Consistent crosscuts reduce the amount of flattening required later.

Step 7: Turn the Slices to Expose the End Grain

Move the twelve crosscut slices to a flat workbench.

Rotate each piece 90 degrees so the freshly cut end-grain surface faces upward.

This changes the orientation of the wood fibers.

The original lengthwise grain now runs vertically through the thickness of the future cutting board.

Each slice becomes a row of alternating light and dark wooden squares.

Arrange the pieces side by side with their top surfaces facing upward.

At this stage, the board may look striped because the colors in neighboring rows still line up.

The checkerboard pattern appears in the next step.

Step 8: Reverse Every Other Row to Form the Checkerboard

Keep the first row in its original left-to-right orientation.

Turn the second row 180 degrees end for end in the plane of the board, keeping its end grain facing upward.

Leave the third row unchanged.

Reverse the fourth row in the same way.

Continue alternating until all twelve rows are arranged.

Because the original panel contains an even number of alternating strips, reversing a row changes which wood color appears at its left edge.

The pattern should now alternate in both directions.

A small section will look like this:

RowSquare 1Square 2Square 3Square 4
1MapleWalnutMapleWalnut
2WalnutMapleWalnutMaple
3MapleWalnutMapleWalnut
4WalnutMapleWalnutMaple

Inspect the complete board before applying adhesive.

Check that every light square touches dark squares along its four sides, except at the outside edges.

Also confirm that the row joints close without gaps.

Pro Tip: Do not simply turn every second row upside down. Keep the intended end-grain cutting face upward and reverse the row’s left-to-right color sequence.

Step 9: Complete the Second Glue-Up

Once the dry layout is correct, prepare the clamps and protective cauls.

Keep the numbered rows in order so the checkerboard pattern does not become mixed up.

Apply an even coat of adhesive to the mating side surfaces between neighboring rows.

These surfaces are primarily long-grain wood faces after the slices have been stood on end.

Do not coat the exposed checkerboard cutting surface with glue.

Bring the rows together, maintaining the alternating color arrangement.

Clamp evenly across the assembled board.

Use flat cauls or another suitable alignment method to prevent the rows from moving up or down as pressure increases.

Inspect the surface from different angles.

Correct visible misalignment while the glue remains workable.

A slight amount of squeeze-out is normal, but excessive adhesive should be removed before it becomes difficult to clean.

Leave the board clamped for the period recommended by the adhesive manufacturer.

Allow the glue to cure fully before flattening or trimming.

Step 10: Flatten, Sand, and Finish the Cutting Board

After the second glue-up has cured, inspect the completed checkerboard.

Check the glue joints and confirm that the board has no loose sections.

The cutting surface is now end grain.

Do not feed this finished end-grain assembly through an ordinary thickness planer.

Planer knives can catch the exposed fiber ends, causing severe tear-out or ejecting pieces of wood.

A drum sander or properly constructed router flattening sled is a safer choice for this stage.

Secure the board, follow the machine instructions, and remove material in controlled passes.

Flatten both faces until the board rests evenly on a counter.

Trim the outside edges using a properly supported setup, if required.

Round the corners and ease the edges with a suitable router bit or sandpaper.

Then sand progressively, beginning with a grit suited to the remaining surface marks and advancing through approximately 120, 180, and 220 grit.

Remove all sanding dust.

A light wipe with clean water can raise loose surface fibers. Allow the board to dry fully, then sand lightly again with fine sandpaper.

Apply food-grade mineral oil to every surface, including the edges and underside.

Allow it to absorb, wipe away the excess, and repeat as directed by the oil manufacturer.

A final coat of cutting-board wax may be added after oiling.

The board is ready for use once the finish has been applied according to its instructions and no excess oil remains.

Key Takeaway: Accurate milling, two properly cured glue-ups, and reversing alternate rows create the checkerboard. Flatten the completed end-grain surface with a suitable router sled or sanding machine rather than an ordinary thickness planer.

Common Checkerboard Cutting Board Mistakes and How to Fix Them

Even small errors can become visible after the rows are glued together.

Most problems originate from inconsistent stock dimensions, incorrect row orientation, or poor alignment during assembly.

Checkerboard Squares Do Not Line Up

Misaligned squares often result from inconsistent strip widths or wood thickness.

For example, strips prepared at slightly different widths can produce uneven vertical joints across the checkerboard.

The pattern can also look wrong if every second row was not reversed.

Before the second glue-up, arrange every row and inspect the pattern from directly above.

Correct the sequence before applying adhesive.

If the first panel has already been cut into slices of different thicknesses, check the variation before assembling them.

Minor surface differences may be removed during flattening, but inconsistent square dimensions or sideways offsets cannot always be corrected afterward.

Gaps Appear Between Wooden Blocks

Gaps usually indicate that the mating surfaces were not flat or the rows shifted during clamping.

Inspect the cut faces and the edges that will form the second glue joints.

A saw blade that produces angled or rough cuts can make tight assembly difficult.

Correct the surfaces before applying glue.

Also check that clamping pressure is distributed evenly.

Do not rely on additional glue to fill wide structural gaps.

If a major gap remains after curing, rebuilding the affected section is generally more dependable than trying to conceal it with filler.

The Finished Board Is Uneven or Warped

Surface unevenness can result from slices moving during the second glue-up.

A router sled or drum sander can remove minor height differences.

Warping may develop from uneven wood moisture, poor stock preparation, or unsuitable drying conditions.

Condition the hardwood in a stable indoor environment before construction, and avoid gluing wood that is excessively wet.

After completion, wash and dry both sides of the cutting board.

A board with severe distortion or separating glue joints may require reconstruction or replacement.

Key Takeaway: Dry fitting and accurate stock preparation prevent most pattern problems. Correct gaps and alignment issues before the final glue-up rather than relying on sanding or wood filler afterward.

Can You Make a Checkerboard Cutting Board Without a Table Saw?

Yes, but the project still requires accurate, square cuts and properly prepared wood.

A sliding miter saw with sufficient cutting capacity may be suitable for some crosscuts, provided the workpiece is securely supported and the cutting setup is appropriate.

A track saw with a suitable guide and clamping arrangement may also be used for certain cuts.

For the long hardwood strips, pre-milled stock can reduce the amount of cutting and surfacing required.

A woodworking shop can prepare the original strips to matching dimensions.

The first glue-up can then be completed using clamps and a flat workbench.

For the second stage, the striped panel needs to be crosscut into matching slices. This is the operation where a precision sled or guided cutting system is most useful.

A random-orbit sander can smooth an already flat board, but removing substantial end-grain unevenness with it may be slow and can round the surface unintentionally.

A router sled or drum sander is preferable when significant flattening is required.

I would avoid attempting this project with only a handheld saw and basic sandpaper if accurate square alignment is the main goal.

A simpler edge-grain striped cutting board is a more manageable first woodworking project when precision cutting equipment is unavailable.

How to Clean and Maintain a Homemade Checkerboard Cutting Board

Proper care protects the hardwood, reduces moisture-related movement, and preserves the glued joints.

A checkerboard board has numerous joints, making drying and surface inspection important.

Cleaning After Food Preparation

Wash the board by hand with hot, soapy water after use.

Use a soft brush or sponge to remove food particles from the cutting surface.

Rinse thoroughly with clean water.

Wipe away excess moisture and position the board so air can reach both sides.

Avoid soaking the board or putting a laminated end-grain cutting board in a dishwasher.

The USDA recommends using separate cutting boards for raw meat, poultry, and seafood and for ready-to-eat foods such as bread and fresh produce.

A homemade wooden board must also be sanitized appropriately after contact with raw animal foods.

Inspect the glue joints regularly. Replace or repair the board if cracks or separation create areas that cannot be cleaned thoroughly.

Oiling and Conditioning the End-Grain Surface

End-grain wood can absorb substantial amounts of conditioning oil because the fiber ends are exposed.

Use food-grade mineral oil when the surface begins looking dry or unevenly conditioned.

Apply oil to the clean, dry board and spread it evenly.

Include the cutting surface, underside, edges, and corners.

Allow the oil to absorb according to the product instructions, then wipe away the excess.

A mineral-oil-and-beeswax conditioner can provide some additional surface water resistance.

There is no universal oiling interval for every handmade cutting board.

Frequency depends on washing habits, wood condition, and kitchen humidity.

Store the board away from standing water, direct sunlight, and strong heat sources.

Key Takeaway: Hand wash the finished board, dry both sides, and condition it when the end grain becomes dry. Inspect the joints regularly for cracks or separation.

Design Variations for Homemade Checkerboard Cutting Boards

After mastering a basic two-color design, the pattern can be adjusted without changing the main construction method.

A few variations are worth considering.

Traditional maple and walnut checkerboard: Light maple and dark walnut create strong contrast and an easily recognizable pattern.

Cherry and maple checkerboard: Cherry produces warmer reddish-brown squares, creating a softer contrast with maple.

Small-square checkerboard: Narrower initial strips produce smaller squares. This requires greater cutting accuracy because small dimensional differences become more noticeable across multiple rows.

Large-square checkerboard: Wider strips and thicker starting stock produce larger blocks. The finished board may also become heavier.

Rectangular checkerboard: If the original strip width differs from its thickness, the visible blocks become rectangles rather than squares.

For a first attempt, I recommend simple square blocks without decorative borders.

A border introduces additional joinery and wood-movement considerations. Full-perimeter borders with grain running in different directions can restrain seasonal expansion and contribute to cracking.

A clean two-color checkerboard is attractive without requiring those extra construction challenges.

Conclusion

The central technique in how to make checkerboard cutting board patterns is the two-stage glue-up. First, alternating hardwood strips are assembled into a striped panel. Then the panel is crosscut, the pieces are turned to expose end grain, and every other row is reversed before the final assembly.

Hard maple and walnut are suitable choices for the pattern because they provide strong color contrast and practical cutting characteristics. Accurate measurements, matching strip dimensions, sound glue joints, and careful flattening produce a smoother and more consistent finished surface.

I recommend completing a smaller practice layout before attempting a large butcher block. Concentrate on square cuts and a precise dry fit, then finish the board with food-grade mineral oil and maintain it through regular hand washing and thorough drying.

FAQs About Making Checkerboard Cutting Boards

What is the best wood for a checkerboard cutting board?

Hard maple and American black walnut are a good combination for a checkerboard cutting board.

Maple provides pale-colored squares with strong dent resistance, while walnut provides dark brown squares and a slightly softer cutting surface.

Both woods can be used in end-grain construction.

Cherry and maple are another option, although their color contrast is usually less dramatic.

How thick should a checkerboard cutting board be?

Many end-grain checkerboard cutting boards are made approximately 1¼ to 2 inches thick.

A finished thickness of around 1½ inches provides a substantial cutting surface for everyday kitchen preparation.

The required thickness also affects the crosscut slice measurements.

Cutting the slices slightly oversize leaves enough material for flattening and sanding before the board reaches its final thickness.

What glue should be used for a checkerboard cutting board?

Use a water-resistant or waterproof wood glue whose manufacturer identifies it as suitable for cutting-board construction.

Titebond III Ultimate Wood Glue is a common example.

Its manufacturer states that it complies with U.S. FDA requirements for indirect food contact and meets the ANSI/HPVA Type I water-resistance standard.

Follow the adhesive’s application and curing instructions before machining the glued board or using it for food preparation.

Can you make a checkerboard cutting board without a planer?

Yes. A thickness planer is not required to flatten the completed checkerboard.

A router flattening sled or drum sander can level an end-grain cutting surface.

A planer may be suitable for preparing the original long-grain wooden strips or the first striped panel, subject to the machine instructions.

Avoid running the completed end-grain board through an ordinary thickness planer because the blades may cause severe tear-out or eject pieces of wood.

How do you keep checkerboard squares perfectly aligned?

Start with hardwood strips milled to consistent widths and thicknesses.

Make the crosscut slices using a repeatable cutting setup and verify that each cut is square.

During dry fitting, reverse every other row and inspect the complete checkerboard before gluing.

Use protective cauls and even clamping pressure during the second glue-up to prevent rows from sliding out of alignment.

Can you make a checkerboard cutting board with three types of wood?

Yes, but a three-color design requires more careful planning.

The colors can be arranged in repeating sequences or decorative patterns using the same general end-grain construction process.

Reversing every other row of a three-color panel does not automatically create the simple alternating checkerboard produced by two colors.

Draw the complete pattern and test the row arrangement before cutting or gluing.

How long does it take to make a checkerboard cutting board?

The project usually spans more than one day because it requires two separate glue-ups and adequate adhesive curing time.

Cutting and milling the wood, assembling the first panel, producing the crosscut slices, arranging the checkerboard, and finishing all require additional working time.

For Titebond wood glues, the manufacturer recommends avoiding stress on new joints for at least 24 hours under typical conditions.

Allow enough time for each glue-up to cure rather than rushing the project.

Can a homemade checkerboard cutting board be used for raw meat?

Yes, a properly constructed and maintained hardwood checkerboard cutting board may be used for raw meat preparation.

The board must have smooth, intact surfaces and joints that do not trap food residue.

The USDA recommends separating cutting surfaces used for raw meat, poultry, and seafood from those used for ready-to-eat foods.

Wash and sanitize the board appropriately after raw animal food preparation, then rinse and dry it thoroughly. Replace or repair the board if deep cracks or damaged joints prevent proper cleaning.

Similar Posts